L. S. L. Elements. (C) Carbon, max. (Mn) Manganese, max. Amardeep Steel Centre is one of the leader manufacturers, Supplier and exporters of high quality ASTM A Stainless Steel Rectangular Tube, ASTM A Global Steel is one of the leading manufacturers, Supplier and exporters of High Quality ASTM A Steel Pipes, ASTM A Polished Stainless Steel Pipes.
|Published (Last):||7 March 2013|
|PDF File Size:||4.53 Mb|
|ePub File Size:||20.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
ASTM A554 Specification
A polished stainless steel ornamental tubes are widely used for building constructions and architectural applications. For sized over 5-in. Where ellipses … appear in this table, there is no minimum and analysis for the element need not be determined or reported. We can offer polished stainless steel pipes in NO.
Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Largest Specified Outside Dimension, Inches. Tied with steel trips, then wrapped by plastic material. Also see Footnote Wstm. Material meeting the requirements of S, S, or S may, by agreement between purchaser and manufacturer, be certified as S The values given in parentheses are mathematical conversions a54 SI units that are provided for information only and are not considered standard.
Link to Active This link will always route to the current Active version of the standard. Tolerances Hot Finished Round Table. For sizes up to and including 5-in.
Small outside diameter tubes are defined as those less than 0. Small outside diameter tubes are defined as those less than 0. Historical Version s – view previous versions of standard.
Material meeting the requirements of S, S, or S may, by x554 between purchaser and manufacturer, be certified as S E These tolerances apply to cut lengths up to and including 24 feet.
ASTM A554 304/304L/304H Stainless Steel EFW Tubes
B For ovality values, the tolerance for average outside diameter at any one cross section does not exceed the outside diameter tolerance value for the applicable outside diameter. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Tubes shall be furnished in one of the following shapes – round, square, rectangular, or special. This abstract is a brief summary of astj referenced standard.
ASTM A Specification | Penn Stainless Products
Tensile Strength, min ksi MPa. A Grade Tube.
Permissible Variations in Cut Length in. For square or rectangular structural tubing with heavier walls, the radius of any outside corner of the section shall not exceed three times the specified wall thickness. Unless otherwise specified in the ordering information, an order specifying S or Typeshall be satisfied by any one of S, S, or S at the option of the seller.
The straightness tolerance is 0. Ovality is the difference between maximum and minimum outside diameters measured at any one cross section. ASTM does not give any warranty express or implied or make any representation that atsm contents of this abstract are accurate, complete or up to date. Up to 6 meters, custom cut lengths Thickness: It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
This guide covers standard specification for welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed.
A welded stainless steel tubing for mechanical applications where appearance, mechanical properties, or corrosion resistance is needed in a number of standard sizes and grades.
Nominal Pipe Size Inches.
Bright Annealed, Polished Trade Name: Radii of Corners, max. Click here For more ss material price list. A Grade L Tube. Yield Strength min, ksi MPa. Heat analysis shall be performed wherein several grades of steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, titanium, columbium, and tantalum. Ratio of Wall Thickness to Outside Aetm.
Ornamental Tube – A – Chicago Tube & Iron
Elongation in 2 in. Aatm, the wall thickness can vary 15 percent over and under that specified, and the inside diameter is governed by both the outside diameter and wall thickness tolerances.
The average of maximum and minimum outside diameter readings should fall within the outside diameter tolerances as shown in this table.