The CDBM CDBC is a quad bilateral switch in- tended for the transmission or multiplexing of analog or digi- tal signals It is pin-for-pin compatible with. The contains 4 analogue bilateral switches, each with an active-high enable input (A) and two input/outputs (X and Y). When the enable input is set high. Page 1. Data sheet acquired from Harris Semiconductor. SCHS Page 2. Page 3. Page 4. Page 5. Page 6. IMPORTANT NOTICE. Texas Instruments and its.
|Published (Last):||10 March 2008|
|PDF File Size:||15.42 Mb|
|ePub File Size:||11.9 Mb|
|Price:||Free* [*Free Regsitration Required]|
So current can flow in one direction and the other direction, depending on which side is the input.
What this means is we feed an analog signal into the input of the switch and it reaches the output only if a HIGH digital signal is fed into the control or enable terminal. This enables the signal at the input to go to the output. V DD and ground, pins 14 and 7, are the power pins. It can be obtained cheaply at a number of online electronic retailers. A bilateral switch acts as a single pole, single throw switch.
Practical Electronics/IC/ – Wikibooks, open books for an open world
The quad bilateral switch chip is a chip that is made up of 4 switches. Each switch also has a control or enable terminal. The is a quad bilateral switch circuit, meaning that is composed of 4 switches. When unpressed, the pushbutton has the signal LOW by default.
The pinout of the chip is shown below. You can view the control terminal as the signal which closes the switch so that the input signal can cross over to the output. The switches are labeled from 1 to 4. Applying these principles, you can easily see how to use all 4 switches if wanted. As the quad term implies, the is composed up of 4 switches. Each switch has an input, output, fd4066 control terminal. With the control switch HIGH, then the switch dataaheet and there can be an output.
In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. If a signal is fed into the input while the pushbutton is unpressed, no signal will appear at the output.
The datasheet for the can be found at the following link: How the Circuit Works So, in order for this circuit to work, the pushbutton must be pressed down for each of the datashert. So you will see that if you press down the pushbutton with an analog signal or digital signal at the input, that same signal will appear at hte output.
How to Build a 4066 Quad Bilateral Switch Circuit
When pressed down, the pushbutton makes the signal HIGH. First, to power thewe connect 5V of power to V DDpin 14, and we connect the ground pin, pin 7, to ground. This establishes sufficient power to the chip. Each switch has a single input and a single output terminal. The control terminal enables the input to go to output.
How to Build a Quad Bilateral Switch Circuit
The really functions as an analog switch. So by a HIGH digital signal fed into the control terminal, we can pass an analog signal from the input terminal to the output terminal of the switch.
In this circuit, we will show the basic functionality of the chip by passing analog signals through 2 of the switches by digital control. The is a pin chip. One place it can be obtained is at Taydaelectronics at the following link: For this circuit, we are only going to be using 2 of the 4 switches.
To the control terminals of the 2 switches, we connect a pull-down resistor pushbutton circuit.
The is an IC composed of switches which are designed to switch analog signals via digital control. In order for signals to pass through from the input side to the output side, the control or enable terminal must be HIGH. The has a wide operating voltage of 5VV.
Without the control or enable switch, there can be no output. How to Build a Quad Bilateral Switch Circuit In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. This means that either side of the switch can be used as the input.
The most common waveform is a sine wave. To the inputs of the 2 switches, we feed an analog signal. A bilateral switch is so called because the switch can operate forward or reverse. If the pushbuttons are not pressed down, then no signal will appear at the outputs.